Product Information
Table of Contents
New Holland TM Series Tractors Workshop Manual Table of Contents
General Information
- Introduction
- Safety Precautions
- Vehicle Identification
Section 00 - General Instructions and Health and Safety
- General Instructions and Health and Safety - Chapter 1
- Page 2: Torques
- Page 3: Special Tools
Section 10 - Engine
-
Separating and Removing The Engine - Chapter 1
- Page 4: Separating Front Axle and Front Support from Engine
- Page 14: Separating Engine and Front Support from Transmission
- Page 21: Engine Removal
-
7.5L CNH Engine - Chapter 2
- Page 2: Specifications
- Page 8: Greases and Sealants
- Page 10: Tightening Torques
- Page 12: Special Tools
- Page 13: Fault Finding
- Page 17: Description and Operation
- Page 24: Engine Overhaul-Introduction
- Page 25: Injection Pump Timing Check
- Page 28: Engine Disassembly and Overhaul
- Page 28: Cylinder Head, Valves and Related Parts
- Page 38: Hydraulic Tappets-Adjustment
- Page 40: Front Cover and Timing Gears
- Page 44: Oil Pan
- Page 45: Flywheel
- Page 46: Rear Cover Plate
- Page 47: Oil Pump
- Page 49: Oil Pressure Relief Valve
- Page 50: Camshaft, Tappets and Camshaft Bearings
- Page 53: Pistons and Cylinder Block
- Page 62: Crankshaft
- Page 66: Crankshaft Front Seal Installation
- Page 67: Engine compression test
-
Cooling System
- Page 68: Description of Operation
- Page 70: Troubleshooting
- Page 71: Specifications
- Page 72: Overhaul
Section 10 - Fuel System - Chapter 3
- Fuel System
- Page 2: Specifications
- Page 2: Torques
- Page 3: Special Tools
- Page 4: Description and Operation
- Page 8: Bosch VE Type Mechanically Controlled Fuel Injection System - Removal
- Page 9: Bosch VE Type Pump Timing and Installation
- Page 13: Bosch VP Electronically Controlled Fuel Injection System - Removal
- Page 14: Bosch VP Electronically Controlled Fuel Injection System - Timing Check
- Page 17: Injection System Bleeding
- Page 18: Injection System Testing and Overhaul
- Page 23: Electric Lift Pump - Removal
- Page 23: Electric Lift Pump - Testing
- Page 24: Turbocharger - Removal
- Page 25: Turbocharger - Disassembly
- Page 25: Turbocharger - Inspection - Reassembly - Installation
- Page 28: Air Cleaner - Removal - Overhaul
- Page 31: Main Fuel Tank - Removal and Installation
- Page 32: Auxiliary Fuel Tank - Removal and Installation
- Page 32: Crankcase Ventilation
- Page 33: Foot Throttle Cable - Replacement and Adjustment
- Page 33: Hand Throttle Cable - Replacement and Adjustment
Section 18 - Clutches - Chapter 1
- Clutches
- Page 1: Specifications
- Page 2: Tightening Torques
- Page 3: Sectional Views
- Page 4: Special Tools
- Page 4: Description and Operation
- Page 4: Troubleshooting
- Page 6: Clutch Removal-Installation
- Page 8: Hydraulic Control Assembly Removal-Installation
- Page 10: Hydraulic Control Assembly Disassembly-Reassembly
Section 21 - Transmission System
-
Semi-Powershift Transmission (Range Command) - Chapter 1
- Page 1: Specifications
- Page 3: Tightening Torques
- Page 5: Special Tools
- Page 9: Sectional Views
- Page 12: Description and Operation
- Page 20: Pressure Testing
- Page 24: Calibration
- Page 27: Removal - Installation - Overhaul
-
Power Command 30 and 40 kph Transmission, 120 - 155 Models (Full Powershift) - Chapter 2
- Page 2: Specifications
- Page 5: Tightening Torques
- Page 10: Special Tools
- Page 13: Transmission Cross Section
- Page 16: Description and Operation and Power Flows
- Page 34: Clutch Calibrations
- Page 39: Pressure Testing
- Page 42: Error Codes and Fault Finding
- Page 46: Limp Home Tool
- Page 47: Transmission Removal and Installation
- Page 53: Transmission Overhaul - Disassembly
- Page 78: Transmission Overhaul - Reassembly
-
Power Command Transmission, 175 - 190 Models (Full Powershift) - Chapter 3
- Page 2: Specifications
- Page 5: Tightening Torques
- Page 7: Special Tools
- Page 10: Description and Operation
- Page 18: Power Flows
- Page 24: Input Sensors and Output Devices
- Page 27: Controls
- Page 40: Clutch Calibration
- Page 44: Pressure Testing
- Page 47: Error Codes and Fault Finding
- Page 51: Limp Home
- Page 52: Transmission Housing - Removal and Installation
- Page 59: Transmission Disassembly
- Page 72: Oil Manifold Bushes, Removal and Installation
- Page 73: Transmission Upper Speed Shaft End Float Adjustment
- Page 74: Clutch Overhaul
- Page 86: Transmission Rear Housing - Disassembly
- Page 88: Transmission Reassembly
- Page 96: Output Shaft End Flow Adjustment
- Page 97: Medium Shaft End Float Adjustment
-
Dual Command Transmission (HI-LO) - Chapter 4
- Page 1: Specifications
- Page 4: Tightening Torques
- Page 6: Special Tools
- Page 10: Sectional Views
- Page 12: Description and Operation
- Page 16: Clutch and Synchroniser Calibration
- Page 19: Pressure Testing
- Page 22: Error Codes and Fault Finding
- Page 28: Limp Home
- Page 29: Transmission Removal and Installation
- Page 32: Transmission Overhaul
- Page 46: Shuttle Gear Bearing Adjustment
- Page 48: Range Input and Output Shaft Bearing Adjustment
- Page 51: HI LO Transmission Valve - Overhaul
- Page 54: HI LO Transmission Control Assembly
This comprehensive manual includes detailed information about the New Holland TM130, TM140, TM155, TM175, and TM190 tractors, making it an essential tool for mechanics, technicians, and owners. It provides in-depth explanations of the engine, transmission, hydraulic system, electrical system, suspension and steering, climate control, maintenance procedures, and troubleshooting techniques.
The price of this manual, handbooks, and repair guides are not set by our marketplace, but by the seller of the manuals themselves, so it is possible that the same manuals are offered at different prices on other pages here. Please compare prices before deciding to purchase.
For many of our manuals, there are comments and ratings from other users at the end of the detail page to make your purchase decision easier. Please leave a review after your purchase to help other users make their purchasing decision.
Don't hesitate and download the repair manual you need now. You get a lifetime guarantee for the download, as described in our FAQs here.
To contact the seller of the manual, please use our contact form here and we will forward your request or take care of it directly.
Comments